Danville, IL
What we run into on Danville floors
Danville's industrial history left it with a lot of older shop and warehouse space, and those floors tend to arrive with the full set of problems at once: oil-soaked concrete, spalling at the dock doors, joints that have opened up under years of wheel traffic, and often an old coating that is already letting go in sheets. That is fine — it just means the prep day is a real day. Degrease it, strip whatever is failing, blast the profile open, fix the joints, and then it will take a coating that holds. On the residential side, the North Street Historic District and the older streets around Lincoln Park run to pre-1930 homes with detached garages off the alley, on thin original slabs. Vermilion Heights and the mid-century neighborhoods are a more typical ranch-and-attached-garage proposition. We also cover the smaller towns around Danville — Tilton, Westville, Georgetown and out toward Kickapoo State Recreation Area.
Garages
Garage Floor Coating in Danville, IL
Garage floor coating in Danville is mostly older-slab work, and the apron is nearly always the problem area. Decades of freeze-thaw and salt take the top layer off the concrete right where the overhead door sits, and if that is coated over without being repaired it will fail there first and take the surrounding floor with it. We patch and re-level the apron, chase and fill the cracks, grind the whole slab, then coat. Flake is the default recommendation here because it hides repaired areas so much better than solid color does, and on a garage that has been standing since the 1920s there will be repaired areas.
Epoxy floor quote in Danville?
(217) 417-5950Call and tell us the room. We cover Vermilion County with no trip charge, and we can usually say on the phone roughly what your slab will need.
Prefer to type it out? Send the quote form instead or email dpflooringservicesllc@gmail.com.
Service area
Where Danville sits in our range
Thirty-five minutes east on I-74. Danville, Tilton, Westville, Georgetown and Hoopeston are all inside the service radius.
We are based in Champaign County and work 50+ miles in every direction, so Danville and the rest of Vermilion County are well inside it, along with Tilton, Westville, Georgetown, Hoopeston.
Call (217) 417-5950 and we will tell you straight away when we can get out to look at it.
Map shows the Danville, IL area we cover.
Services
What we install in Danville
All six services are available across Vermilion County and the surrounding towns.
Nearby
Other towns we cover
- Epoxy Flooring in Champaign, IL
- Epoxy Flooring in Urbana, IL
- Epoxy Flooring in Savoy, IL
- Epoxy Flooring in Mahomet, IL
- Epoxy Flooring in Rantoul, IL
- Epoxy Flooring in Bloomington, IL
- Epoxy Flooring in Normal, IL
- Epoxy Flooring in Decatur, IL
- Epoxy Flooring in Monticello, IL
- Epoxy Flooring in Tuscola, IL
- Epoxy Flooring in Paxton, IL
- Epoxy Flooring in Clinton, IL
- Epoxy Flooring in Tolono, IL
Questions
Before you book a Danville quote
How long does epoxy take to cure?
Most floors are ready for light foot traffic about 12 to 24 hours after the final coat, furniture and light use at 24 to 72 hours, and vehicle traffic after roughly 5 to 7 days. Full chemical cure takes about a week.
Those windows move with temperature and humidity, so we give you the exact dates for your floor before we start. And we would much rather tell you to wait two extra days than watch tire marks press permanently into a coating that was still green.
How long does an epoxy floor last?
A properly prepped residential garage or basement floor commonly runs 10 to 20 years. Commercial and industrial floors under forklifts, steel wheels and constant traffic are usually in the 5 to 10 year range before they want a recoat — and a recoat is far cheaper than a new install, because the prep is already done.
The single biggest factor is not the epoxy. It is the surface prep underneath it. That is exactly why we grind every floor instead of acid-etching it and hoping for the best.
Can you put epoxy over an existing floor?
Over bare concrete — yes. That is the ideal surface, and we grind it first to open the pores so the coating can key into it.
Over an existing coating — it depends. If the old coating is sound and well bonded, we can abrade it and go over the top. If it is peeling, chipping, bubbling or flaking, it has to come off first — and we do that too.
Over tile, wood, vinyl or carpet — no. Epoxy needs concrete to bond to, so those have to be removed first. We will tell you which situation you are in at the estimate, before you have committed to anything.
How much does epoxy flooring cost?
Epoxy is priced by the square foot, and four things move the number:
- Square footage. Bigger floors cost less per foot — the setup is the same whether the room is 400 or 4,000 square feet.
- Slab condition. A clean, sound slab needs a grind. One with cracks, spalling, pits or an old failing coating needs repair work first.
- The system you pick. Solid color is the most economical, full flake sits in the middle, and metallic is the premium option.
- Extras. Non-slip aggregate, line striping, cove base and heavier build thicknesses all add to it.
We will not quote a floor we have not seen, because a number pulled over the phone helps nobody. Call (217) 417-5950 and we will come measure. The estimate is free, itemized and in writing, so you can see exactly what you are paying for.
Get a free Danville quote
On-site, itemized and in writing — with no trip charge anywhere in Vermilion County.